High quality 3 in 1 dehumidification dryer plastic drying machine manufacturer

3 in 1 dehumidification dryer specification parameters

The purpose, function, and effectiveness of a three in one dehumidifier dryer

Three-in-one dehumidification dryer is suitable for: engineering plastic raw materials with strong hygroscopic properties, such as PA, PC, LCP, PBT, PET, etc.

Using ceramics using honeycomb wheel dehumidification, set dehumidification, drying, two section feeding three functions in one, and can choose three feeding function, the maximum can achieve a pair of five machines.

The three in one dehumidifier dryer has played an important role in the plastic processing industry through its integrated design and high efficiency advantages, with good plastic product molding effects. When choosing drying equipment, considering its cost-effectiveness and technical performance can optimize the production process and improve product quality.

Plastic molding plastic must be dry to 0.02% below the water content, transparency is not good, pouring channel stick, wool edge, bubbles, silver strip, flow mark, cracking, poor size stability, internal stress, product physical strength and other shortcomings, most of the bad reasons, is that the plastic is not fully dehumidification drying before molding. In particular, high water immersion plastics such as PET, PBT, PA, PC and so on need more ultra-low dew point Dew point-40℃ drying equipment.

This dehumidifier can dry to the water content below 0.02% to solve the problems of poor transparency, pouring adhesion, bubble, silver strip, crack, poor size stability, internal stress, insufficient physical strength and other shortcomings.

Characteristics of Three in One Dehumidification and Drying Machine

1. Dehumidification, drying, two feeding three functions in one, and can choose three feeding function.
2. Stable supply of-40 dew point dehumidification air greatly improve product quality.
3. Low power consumption and high efficacy.(0.6 degrees per hour, 2.5 degrees per hour)
4. The double-layer insulation drying material bucket adopts the lower blowing duct design to prevent heat loss and improve the drying efficiency.
5. All stainless steel upper and lower feeding system, to avoid raw material pollution.
6. Closed circulation moisture and material system, can avoid dry raw materials due to contact with external air and return tide.
7. Use non-free solid state relay to control heating.
8. Fault intelligent alarm, time intelligent reservation.
9. Optical level powder removal type trinity is dedicated to dust-free or purification workshop.
10. Use ceramic honeycomb wheel dehumidification to improve performance and prolong service life, and save maintenance costs.
11. The structure is simple and compact, the machine covers a small area, save space, easy to move, can be replaced at will.
12. Appearance of powder paint, beautiful and generous.
13. Suitable for engineering plastic raw materials with strong hygroscopic properties such as: PA, PC.LCP, PBT, PET, GEPD, etc.

Safety protection system for dehumidification dryer

1. Overcurrent of total power supply without fuse circuit breaker.
2. Overload protection of dehumidification fan inversion.
3. Heat preservation and heat insulation treatment.
4. Abnormal alarm and indicators.
5. Overheat protection temperature switch.
6. Regeneration of high and low temperature error alarm and indicator lamp.
7. Compressed air pressure loss alarm.

Precautions for using dehumidifier dryer

1. Please carry out electrical construction in accordance with the “electrical equipment benchmark”, “internal regulations” and the operation manual.
2. Please do not use the specified power supply.
3. Please complete the specified grounding works.(Yellow power cord)
4. Please tighten the machine body, the connector of the meter wire and the connection terminal.
5. please do not destroy the wire, do not give pressure to the wire, do not place heavy objects on the wire, do not clip the wire. May cause an electric shock.
6. Please conduct the wiring and inspection with technicians.
7. When the machine needs to be disassembled due to inspection and cleaning, please cut off the power supply and compressed air source first.
8. Before the line detection, the power supply must be cut off first, and the voltage must be measured with a multimeter after 10 minutes to ensure the safety.
9. Do not open the control box door at will during the power-up process.
10. Do not touch the machine body, control department and other accessories with wet hands.

Technical parameter table of three-in-one dehumidifier dryer